AS568 · ISO 3601 · MIL-PRF cross-references, 15 compounds
AS568 · 200 series · 0.139 in cross-section

AS568-284 O-Ring

17.955 in inside diameter × 0.139 in cross-section — 456.06 × 3.53 mm. Nominal size 18 ID × 1/8 CS. Available in 15 compounds; 13 military designations map to this size.

Inside dia.17.955in
Cross-section0.139in
Outside dia.18.233in
Mil-spec refs137 orderable

01Dimensions

inch values are normative · mm converted at 25.4
Inside dia. 17.955 in · 456.06 mm Outside dia. 18.233 in · 463.12 mm Cross-section 0.139 in · 3.53 mm

Section through the ring: one dash number fixes all three dimensions at once.

Inside diameternominal, not actual17.955in
Cross-sectionnominal0.139in
Outside diametercalculated, ID + 2 × CS18.233in
ID tolerancetypical commercial band±0.030in
CS tolerancetypical commercial band±0.004in
Inside diameter456.06mm
Cross-section3.53mm
Outside diameter463.12mm
ID tolerance±0.76mm
CS tolerance±0.10mm

Tolerance bands are typical commercial values for this cross-section. Where the drawing calls out a tighter or wider band, the drawing governs and we quote to it.

02Military cross-reference

compiled from public catalogue data
6 of these 13 designations are no longer current

5 carry a replacement designation — order that number and the part drops into the same groove. 1 were cancelled with no replacement on record.

We show the current designation so your incoming inspection does not reject a shipment against a document that was withdrawn.

DesignatorCompoundStatusOrder as
AS3209-284FKMStabilizedAS3209C
AS3582-284VMQ siliconeCurrentAS3582
AS9386-284VMQ siliconeCurrentAS9386B
M25988/1-284FVMQActiveAMSR25988B
M25988/2-284FVMQActiveAMSR25988B
M25988/3-284FVMQActiveAMSR25988B
M25988/4-284FVMQActiveAMSR25988B
M83248/1-284FKMCanceledAS83248/1A
M83248/2-284FKMCanceledAS83248/2A
M83461/1-284NBRCanceledAS83461/1C
M83485/1-284FKM, low-temperature gradeCanceledNo replacement
MS28775-284NBRInactiveAS28775A
MS29513-284NBRCanceledAS29513C

A dash number fixes a size. A military designator fixes a size and a compound specification. MS28775-284 and M83248/1-284 are the same 17.955 × 0.139 in part in two different materials — they are not interchangeable.

03Available compounds

same tool, 15 materials

Every compound below is moulded in the AS568-284 tool, so the dimensions do not change when you change material. Temperature bands are the continuous service range for the standard formulation.

04Questions we get on this size

What is AS568-284 in millimetres?

456.06 mm inside diameter × 3.53 mm cross-section, outside diameter 463.12 mm. These are converted from the inch values at 25.4 and rounded to two decimals — a metric drawing will normally specify a different, rounder size.

What is the outside diameter?

18.233 in (463.12 mm), calculated as ID + 2 × CS. This is the free, uninstalled diameter. Installed in a groove the ring stretches slightly and the OD you measure on the part will not match this number.

Is a mil-spec number for this size the same part?

Same geometry, different material specification. A designator such as MS28775-284 fixes the compound as well as the size. If you substitute a different compound for the same dash number the part will fit, but its swell in the medium and its compression set at temperature will differ — which is what the material callout was there to control.

Can you make it in FFKM or another special compound?

Yes, to order. FFKM and the perfluoroelastomers are compression moulded for this size rather than transfer moulded, so tooling cost applies and lead time is around four weeks. It is normally only worth it above 200 °C or in solvents that swell FKM.

05Other sizes in this cross-section

0.139 in · 200 series

A groove cut for one 0.139 in section takes any of these. Change the ID without changing the groove depth.

All 0.139 in sizes