AS568 · ISO 3601 · MIL-PRF cross-references, 15 compounds
AS568 · 400 series · 0.275 in cross-section

AS568-447 O-Ring

8.975 in inside diameter × 0.275 in cross-section — 227.96 × 6.99 mm. Nominal size 9 ID × 1/4 CS. Available in 15 compounds; 13 military designations map to this size.

Inside dia.8.975in
Cross-section0.275in
Outside dia.9.525in
Mil-spec refs137 orderable

01Dimensions

inch values are normative · mm converted at 25.4
Inside dia. 8.975 in · 227.96 mm Outside dia. 9.525 in · 241.94 mm Cross-section 0.275 in · 6.99 mm

Section through the ring: one dash number fixes all three dimensions at once.

Inside diameternominal, not actual8.975in
Cross-sectionnominal0.275in
Outside diametercalculated, ID + 2 × CS9.525in
ID tolerancetypical commercial band±0.025in
CS tolerancetypical commercial band±0.006in
Inside diameter227.96mm
Cross-section6.99mm
Outside diameter241.94mm
ID tolerance±0.64mm
CS tolerance±0.15mm

Tolerance bands are typical commercial values for this cross-section. Where the drawing calls out a tighter or wider band, the drawing governs and we quote to it.

02Military cross-reference

compiled from public catalogue data
6 of these 13 designations are no longer current

5 carry a replacement designation — order that number and the part drops into the same groove. 1 were cancelled with no replacement on record.

We show the current designation so your incoming inspection does not reject a shipment against a document that was withdrawn.

DesignatorCompoundStatusOrder as
AS3209-447FKMStabilizedAS3209C
AS3582-447VMQ siliconeCurrentAS3582
AS9386-447VMQ siliconeCurrentAS9386B
M25988/1-447FVMQActiveAMSR25988B
M25988/2-447FVMQActiveAMSR25988B
M25988/3-447FVMQActiveAMSR25988B
M25988/4-447FVMQActiveAMSR25988B
M83248/1-447FKMCanceledAS83248/1A
M83248/2-447FKMCanceledAS83248/2A
M83461/1-447NBRCanceledAS83461/1C
M83485/1-447FKM, low-temperature gradeCanceledNo replacement
MS28775-447NBRInactiveAS28775A
MS29513-447NBRCanceledAS29513C

A dash number fixes a size. A military designator fixes a size and a compound specification. MS28775-447 and M83248/1-447 are the same 8.975 × 0.275 in part in two different materials — they are not interchangeable.

03Available compounds

same tool, 15 materials

Every compound below is moulded in the AS568-447 tool, so the dimensions do not change when you change material. Temperature bands are the continuous service range for the standard formulation.

04Questions we get on this size

What is AS568-447 in millimetres?

227.96 mm inside diameter × 6.99 mm cross-section, outside diameter 241.94 mm. These are converted from the inch values at 25.4 and rounded to two decimals — a metric drawing will normally specify a different, rounder size.

What is the outside diameter?

9.525 in (241.94 mm), calculated as ID + 2 × CS. This is the free, uninstalled diameter. Installed in a groove the ring stretches slightly and the OD you measure on the part will not match this number.

Is a mil-spec number for this size the same part?

Same geometry, different material specification. A designator such as MS28775-447 fixes the compound as well as the size. If you substitute a different compound for the same dash number the part will fit, but its swell in the medium and its compression set at temperature will differ — which is what the material callout was there to control.

Can you make it in FFKM or another special compound?

Yes, to order. FFKM and the perfluoroelastomers are compression moulded for this size rather than transfer moulded, so tooling cost applies and lead time is around four weeks. It is normally only worth it above 200 °C or in solvents that swell FKM.

05Other sizes in this cross-section

0.275 in · 400 series

A groove cut for one 0.275 in section takes any of these. Change the ID without changing the groove depth.

All 0.275 in sizes