Silicone and fluorosilicone look like the same answer to the same question, and they are not. One is a general-purpose elastomer with an unusual temperature range and poor mechanical strength; the other is that same range shifted colder, with oil resistance bought at a considerable price. Choosing between them comes down to which fluid the joint sees.

What they are
VMQ (silicone) is a polysiloxane with a methyl and vinyl side groups. The silicon-oxygen backbone gives it unusual thermal stability and flexibility at low temperature, and it is chemically inert enough to be used in food and medical contact. What it lacks is strength: tensile and tear properties are the lowest of any common sealing elastomer, and it swells badly in most hydrocarbons.
FVMQ (fluorosilicone) replaces some methyl groups with trifluoropropyl groups. The fluorine adds oil and fuel resistance, and the siloxane backbone keeps most of the cold flexibility. The cost is roughly four times silicone, weaker tear strength than FKM, and a lower maximum temperature than either.
The numbers that decide it
| Property | VMQ | FVMQ | FKM | NBR |
|---|---|---|---|---|
| Continuous range | −54 to 204 °C | −73 to 177 °C | −26 to 204 °C | −34 to 100 °C |
| Swell in mineral oil | 30 %+ | 12 % | 5 % | 5 % |
| Swell in jet fuel | severe | moderate | low | moderate |
| Tear strength | low | low | good | good |
| Relative cost | 3 | 12 | 7 | 1 |
The table contains the whole decision. VMQ is the widest temperature range with the worst oil resistance; FVMQ is the widest cold range with moderate oil resistance at four times the price; FKM has the lowest swell in oil and a poor cold limit.
Where silicone is the right answer
- Hot air and dry heat, where no oil is present. A silicone ring in an oven door or a heater duct at 200 °C will outlast most alternatives.
- Cold static seals in equipment that sees no hydrocarbon: outdoor instrumentation, cold-climate water lines, food processing.
- Food, beverage and pharmaceutical contact, where an inert, extractable-controlled compound is required and the media are aqueous.
- Electrical and electronic sealing, where the compound's dielectric properties and ozone resistance matter.
- Applications where conformability matters more than strength — silicone is soft and compliant, which helps on rough or irregular surfaces at low pressure.
Silicone's weakness in oil is not marginal: in mineral oil it can swell by 30 % or more, which fills a normal groove and turns a soft seal into an incompressible plug. A silicone ring in an oil line is a design error, not a marginal choice.
Where fluorosilicone is worth the price
- Fuel and oil at low temperature. This is FVMQ's defining application: aircraft fuel systems, fuel-line seals, and cold-climate equipment that sees hydrocarbon.
- Joints that see both cold and fuel — the combination that eliminates both VMQ (swells) and FKM (too stiff when cold).
- Aerospace specifications that call for FVMQ by designation (the M25988 family is the classic example).
What FVMQ is not: a general-purpose oil seal. At 12 % swell in mineral oil it is workable but not dry; FKM at 5 % is better, cheaper and has a higher temperature limit. Choose FVMQ only when the cold requirement rules out FKM.
if the fluid is hydrocarbon and the joint goes below −40 °C, FVMQ. If the fluid is hydrocarbon and the joint stays above −20 °C, FKM. If the fluid is not hydrocarbon and the joint is hot or cold, VMQ.
Mechanical limitations both share
Both compounds are weak in tear and in tensile strength compared with NBR or FKM. That has three consequences:
- They are poor choices for dynamic service, especially reciprocating rods, where tear resistance governs life.
- They are easily damaged at installation, so the chamfer and deburring requirements are stricter than for a nitrile ring.
- They take a set under high compressive load, particularly at temperature, and the set is worse than FKM's.
Silicone also has high gas permeability, which matters in vacuum and in gas service: a silicone seal in a vacuum chamber can be a virtual leak, and in high-pressure gas it is a poor choice for RGD resistance.
Contamination: the problem nobody specifies
Silicone migrates. Low-molecular-weight siloxanes can transfer from the ring to adjacent surfaces, and in painting, coating, bonding, and electronics assembly that transfer is a defect — it causes fish-eyes in paint and poor adhesion in bonded joints.
If the product is painted or bonded anywhere near the seal, silicone is the wrong material regardless of its temperature performance. Fluorosilicone has the same issue at a lower level. This is one of the few cases where a material is eliminated by the factory environment rather than by the service conditions.
Specifying either one
State four things and the compound choice becomes unambiguous:
- Fluid, by name, including whether it is hydrocarbon.
- Minimum temperature with the soak duration.
- Maximum continuous temperature, and whether the environment is air or fluid.
- Whether the part is painted, bonded, or used in a cleanliness-critical assembly.
Without item 4, a silicone seal can pass every mechanical test and still cause a paint defect downstream.
Frequently asked questions
Is fluorosilicone better than silicone?
It is better in hydrocarbon fluids and at lower temperatures, and worse in cost, tear strength and maximum temperature. For a dry-heat application with no oil, silicone is the better choice.
Can silicone be used with oil at all?
Only where the exposure is incidental. In mineral oil silicone swells by roughly 30 %, which is enough to fill a normal groove and lock the joint.
Why is fluorosilicone so expensive?
The fluoropropyl groups require a more complex monomer and a more demanding polymerisation. The cost is in the chemistry, not in the volume, which is why FVMQ prices are relatively insensitive to order size.
Does silicone cause paint defects?
Yes. Siloxanes migrate to adjacent surfaces and cause fish-eyes and adhesion failures in painting and bonding. If the assembly is painted after sealing, silicone should be excluded.
Which one for a cold fuel system?
Fluorosilicone. FKM is too stiff below about −26 °C, and silicone swells in fuel. FVMQ is the only common compound that covers both constraints.