01Dimensions
inch values are normative · mm converted at 25.4Section through the ring: one dash number fixes all three dimensions at once.
| Inside diameternominal, not actual | 6.237 | in |
|---|---|---|
| Cross-sectionnominal | 0.103 | in |
| Outside diametercalculated, ID + 2 × CS | 6.443 | in |
| ID tolerancetypical commercial band | ±0.020 | in |
| CS tolerancetypical commercial band | ±0.004 | in |
| Inside diameter | 158.42 | mm |
|---|---|---|
| Cross-section | 2.62 | mm |
| Outside diameter | 163.65 | mm |
| ID tolerance | ±0.51 | mm |
| CS tolerance | ±0.10 | mm |
Tolerance bands are typical commercial values for this cross-section. Where the drawing calls out a tighter or wider band, the drawing governs and we quote to it.
02Military cross-reference
compiled from public catalogue data5 carry a replacement designation — order that number and the part drops into the same groove. 1 were cancelled with no replacement on record.
We show the current designation so your incoming inspection does not reject a shipment against a document that was withdrawn.
| Designator | Compound | Status | Order as |
|---|---|---|---|
| AS3209-164 | FKM | Stabilized | AS3209C |
| AS3582-164 | VMQ silicone | Current | AS3582 |
| AS9386-164 | VMQ silicone | Current | AS9386B |
| M25988/1-164 | FVMQ | Active | AMSR25988B |
| M25988/2-164 | FVMQ | Active | AMSR25988B |
| M25988/3-164 | FVMQ | Active | AMSR25988B |
| M25988/4-164 | FVMQ | Active | AMSR25988B |
| M83248/1-164 | FKM | Canceled | AS83248/1A |
| M83248/2-164 | FKM | Canceled | AS83248/2A |
| M83461/1-164 | NBR | Canceled | AS83461/1C |
| M83485/1-164 | FKM, low-temperature grade | Canceled | No replacement |
| MS28775-164 | NBR | Inactive | AS28775A |
| MS29513-164 | NBR | Canceled | AS29513C |
A dash number fixes a size. A military designator fixes a size and a compound specification. MS28775-164 and M83248/1-164 are the same 6.237 × 0.103 in part in two different materials — they are not interchangeable.
03Available compounds
same tool, 15 materialsEvery compound below is moulded in the AS568-164 tool, so the dimensions do not change when you change material. Temperature bands are the continuous service range for the standard formulation.
04Questions we get on this size
What is AS568-164 in millimetres?
158.42 mm inside diameter × 2.62 mm cross-section, outside diameter 163.65 mm. These are converted from the inch values at 25.4 and rounded to two decimals — a metric drawing will normally specify a different, rounder size.
What is the outside diameter?
6.443 in (163.65 mm), calculated as ID + 2 × CS. This is the free, uninstalled diameter. Installed in a groove the ring stretches slightly and the OD you measure on the part will not match this number.
Is a mil-spec number for this size the same part?
Same geometry, different material specification. A designator such as MS28775-164 fixes the compound as well as the size. If you substitute a different compound for the same dash number the part will fit, but its swell in the medium and its compression set at temperature will differ — which is what the material callout was there to control.
Can you make it in FFKM or another special compound?
Yes, to order. FFKM and the perfluoroelastomers are compression moulded for this size rather than transfer moulded, so tooling cost applies and lead time is around four weeks. It is normally only worth it above 200 °C or in solvents that swell FKM.
05Other sizes in this cross-section
0.103 in · 100 seriesA groove cut for one 0.103 in section takes any of these. Change the ID without changing the groove depth.