AS568 · ISO 3601 · MIL-PRF cross-references, 15 compounds
AS568 · 300 series · 0.210 in cross-section

AS568-346 O-Ring

4.100 in inside diameter × 0.210 in cross-section — 104.14 × 5.33 mm. Nominal size 4-1/8 ID × 3/16 CS. Available in 15 compounds; 13 military designations map to this size.

Inside dia.4.100in
Cross-section0.210in
Outside dia.4.520in
Mil-spec refs137 orderable

01Dimensions

inch values are normative · mm converted at 25.4
Inside dia. 4.100 in · 104.14 mm Outside dia. 4.520 in · 114.81 mm Cross-section 0.210 in · 5.33 mm

Section through the ring: one dash number fixes all three dimensions at once.

Inside diameternominal, not actual4.100in
Cross-sectionnominal0.210in
Outside diametercalculated, ID + 2 × CS4.520in
ID tolerancetypical commercial band±0.015in
CS tolerancetypical commercial band±0.005in
Inside diameter104.14mm
Cross-section5.33mm
Outside diameter114.81mm
ID tolerance±0.38mm
CS tolerance±0.13mm

Tolerance bands are typical commercial values for this cross-section. Where the drawing calls out a tighter or wider band, the drawing governs and we quote to it.

02Military cross-reference

compiled from public catalogue data
6 of these 13 designations are no longer current

5 carry a replacement designation — order that number and the part drops into the same groove. 1 were cancelled with no replacement on record.

We show the current designation so your incoming inspection does not reject a shipment against a document that was withdrawn.

DesignatorCompoundStatusOrder as
AS3209-346FKMStabilizedAS3209C
AS3582-346VMQ siliconeCurrentAS3582
AS9386-346VMQ siliconeCurrentAS9386B
M25988/1-346FVMQActiveAMSR25988B
M25988/2-346FVMQActiveAMSR25988B
M25988/3-346FVMQActiveAMSR25988B
M25988/4-346FVMQActiveAMSR25988B
M83248/1-346FKMCanceledAS83248/1A
M83248/2-346FKMCanceledAS83248/2A
M83461/1-346NBRCanceledAS83461/1C
M83485/1-346FKM, low-temperature gradeCanceledNo replacement
MS28775-346NBRInactiveAS28775A
MS29513-346NBRCanceledAS29513C

A dash number fixes a size. A military designator fixes a size and a compound specification. MS28775-346 and M83248/1-346 are the same 4.100 × 0.210 in part in two different materials — they are not interchangeable.

03Available compounds

same tool, 15 materials

Every compound below is moulded in the AS568-346 tool, so the dimensions do not change when you change material. Temperature bands are the continuous service range for the standard formulation.

04Questions we get on this size

What is AS568-346 in millimetres?

104.14 mm inside diameter × 5.33 mm cross-section, outside diameter 114.81 mm. These are converted from the inch values at 25.4 and rounded to two decimals — a metric drawing will normally specify a different, rounder size.

What is the outside diameter?

4.520 in (114.81 mm), calculated as ID + 2 × CS. This is the free, uninstalled diameter. Installed in a groove the ring stretches slightly and the OD you measure on the part will not match this number.

Is a mil-spec number for this size the same part?

Same geometry, different material specification. A designator such as MS28775-346 fixes the compound as well as the size. If you substitute a different compound for the same dash number the part will fit, but its swell in the medium and its compression set at temperature will differ — which is what the material callout was there to control.

Can you make it in FFKM or another special compound?

Yes, to order. FFKM and the perfluoroelastomers are compression moulded for this size rather than transfer moulded, so tooling cost applies and lead time is around four weeks. It is normally only worth it above 200 °C or in solvents that swell FKM.

05Other sizes in this cross-section

0.210 in · 300 series

A groove cut for one 0.210 in section takes any of these. Change the ID without changing the groove depth.

All 0.210 in sizes