AS568 · ISO 3601 · MIL-PRF cross-references, 15 compounds
AS568 · 900 series · 0.082 in cross-section

AS568-907 O-Ring

0.530 in inside diameter × 0.082 in cross-section — 13.46 × 2.08 mm. Nominal size 7/16 ID × — CS. Available in 15 compounds; 4 military designations map to this size.

Inside dia.0.530in
Cross-section0.082in
Outside dia.0.694in
Mil-spec refs41 orderable

01Dimensions

inch values are normative · mm converted at 25.4
Inside dia. 0.530 in · 13.46 mm Outside dia. 0.694 in · 17.63 mm Cross-section 0.082 in · 2.08 mm

Section through the ring: one dash number fixes all three dimensions at once.

Inside diameternominal, not actual0.530in
Cross-sectionnominal0.082in
Outside diametercalculated, ID + 2 × CS0.694in
ID tolerancetypical commercial band±0.007in
CS tolerancetypical commercial band±0.003in
Inside diameter13.46mm
Cross-section2.08mm
Outside diameter17.63mm
ID tolerance±0.18mm
CS tolerance±0.08mm

Tolerance bands are typical commercial values for this cross-section. Where the drawing calls out a tighter or wider band, the drawing governs and we quote to it.

02Military cross-reference

compiled from public catalogue data
3 of these 4 designations are no longer current

1 carry a replacement designation — order that number and the part drops into the same groove. 2 were cancelled with no replacement on record.

We show the current designation so your incoming inspection does not reject a shipment against a document that was withdrawn.

DesignatorCompoundStatusOrder as
AS3208-07FKMStabilizedAS3208A
AS9385-07VMQ siliconeCanceledNo replacement
M83461/2-907NBRCanceledNo replacement
MS29512-07NBRCanceledAS29512C

A dash number fixes a size. A military designator fixes a size and a compound specification. MS28775-907 and M83248/1-907 are the same 0.530 × 0.082 in part in two different materials — they are not interchangeable.

03Available compounds

same tool, 15 materials

Every compound below is moulded in the AS568-907 tool, so the dimensions do not change when you change material. Temperature bands are the continuous service range for the standard formulation.

04Questions we get on this size

What is AS568-907 in millimetres?

13.46 mm inside diameter × 2.08 mm cross-section, outside diameter 17.63 mm. These are converted from the inch values at 25.4 and rounded to two decimals — a metric drawing will normally specify a different, rounder size.

What is the outside diameter?

0.694 in (17.63 mm), calculated as ID + 2 × CS. This is the free, uninstalled diameter. Installed in a groove the ring stretches slightly and the OD you measure on the part will not match this number.

Is a mil-spec number for this size the same part?

Same geometry, different material specification. A designator such as MS28775-907 fixes the compound as well as the size. If you substitute a different compound for the same dash number the part will fit, but its swell in the medium and its compression set at temperature will differ — which is what the material callout was there to control.

Can you make it in FFKM or another special compound?

Yes, to order. FFKM and the perfluoroelastomers are compression moulded for this size rather than transfer moulded, so tooling cost applies and lead time is around four weeks. It is normally only worth it above 200 °C or in solvents that swell FKM.

05Other sizes in this cross-section

0.082 in · 900 series

A groove cut for one 0.082 in section takes any of these. Change the ID without changing the groove depth.

All 0.082 in sizes