AS568 · ISO 3601 · MIL-PRF cross-references, 15 compounds
AS568 · 900 series · 0.097 in cross-section

AS568-910 O-Ring

0.755 in inside diameter × 0.097 in cross-section — 19.18 × 2.46 mm. Nominal size 5/8 ID × — CS. Available in 15 compounds; 4 military designations map to this size.

Inside dia.0.755in
Cross-section0.097in
Outside dia.0.949in
Mil-spec refs41 orderable

01Dimensions

inch values are normative · mm converted at 25.4
Inside dia. 0.755 in · 19.18 mm Outside dia. 0.949 in · 24.1 mm Cross-section 0.097 in · 2.46 mm

Section through the ring: one dash number fixes all three dimensions at once.

Inside diameternominal, not actual0.755in
Cross-sectionnominal0.097in
Outside diametercalculated, ID + 2 × CS0.949in
ID tolerancetypical commercial band±0.007in
CS tolerancetypical commercial band±0.003in
Inside diameter19.18mm
Cross-section2.46mm
Outside diameter24.1mm
ID tolerance±0.18mm
CS tolerance±0.08mm

Tolerance bands are typical commercial values for this cross-section. Where the drawing calls out a tighter or wider band, the drawing governs and we quote to it.

02Military cross-reference

compiled from public catalogue data
3 of these 4 designations are no longer current

1 carry a replacement designation — order that number and the part drops into the same groove. 2 were cancelled with no replacement on record.

We show the current designation so your incoming inspection does not reject a shipment against a document that was withdrawn.

DesignatorCompoundStatusOrder as
AS3208-10FKMStabilizedAS3208A
AS9385-10VMQ siliconeCanceledNo replacement
M83461/2-910NBRCanceledNo replacement
MS29512-10NBRCanceledAS29512C

A dash number fixes a size. A military designator fixes a size and a compound specification. MS28775-910 and M83248/1-910 are the same 0.755 × 0.097 in part in two different materials — they are not interchangeable.

03Available compounds

same tool, 15 materials

Every compound below is moulded in the AS568-910 tool, so the dimensions do not change when you change material. Temperature bands are the continuous service range for the standard formulation.

04Questions we get on this size

What is AS568-910 in millimetres?

19.18 mm inside diameter × 2.46 mm cross-section, outside diameter 24.1 mm. These are converted from the inch values at 25.4 and rounded to two decimals — a metric drawing will normally specify a different, rounder size.

What is the outside diameter?

0.949 in (24.1 mm), calculated as ID + 2 × CS. This is the free, uninstalled diameter. Installed in a groove the ring stretches slightly and the OD you measure on the part will not match this number.

Is a mil-spec number for this size the same part?

Same geometry, different material specification. A designator such as MS28775-910 fixes the compound as well as the size. If you substitute a different compound for the same dash number the part will fit, but its swell in the medium and its compression set at temperature will differ — which is what the material callout was there to control.

Can you make it in FFKM or another special compound?

Yes, to order. FFKM and the perfluoroelastomers are compression moulded for this size rather than transfer moulded, so tooling cost applies and lead time is around four weeks. It is normally only worth it above 200 °C or in solvents that swell FKM.

05Other sizes in this cross-section

0.097 in · 900 series

A groove cut for one 0.097 in section takes any of these. Change the ID without changing the groove depth.

All 0.097 in sizes