AS568 · ISO 3601 · MIL-PRF cross-references, 15 compounds
AS568 · 900 series · 0.116 in cross-section

AS568-911 O-Ring

0.863 in inside diameter × 0.116 in cross-section — 21.92 × 2.95 mm. Nominal size 11/16 ID × — CS. Available in 15 compounds; 4 military designations map to this size.

Inside dia.0.863in
Cross-section0.116in
Outside dia.1.095in
Mil-spec refs41 orderable

01Dimensions

inch values are normative · mm converted at 25.4
Inside dia. 0.863 in · 21.92 mm Outside dia. 1.095 in · 27.81 mm Cross-section 0.116 in · 2.95 mm

Section through the ring: one dash number fixes all three dimensions at once.

Inside diameternominal, not actual0.863in
Cross-sectionnominal0.116in
Outside diametercalculated, ID + 2 × CS1.095in
ID tolerancetypical commercial band±0.007in
CS tolerancetypical commercial band±0.004in
Inside diameter21.92mm
Cross-section2.95mm
Outside diameter27.81mm
ID tolerance±0.18mm
CS tolerance±0.10mm

Tolerance bands are typical commercial values for this cross-section. Where the drawing calls out a tighter or wider band, the drawing governs and we quote to it.

02Military cross-reference

compiled from public catalogue data
3 of these 4 designations are no longer current

1 carry a replacement designation — order that number and the part drops into the same groove. 2 were cancelled with no replacement on record.

We show the current designation so your incoming inspection does not reject a shipment against a document that was withdrawn.

DesignatorCompoundStatusOrder as
AS3208-11FKMStabilizedAS3208A
AS9385-11VMQ siliconeCanceledNo replacement
M83461/2-911NBRCanceledNo replacement
MS29512-11NBRCanceledAS29512C

A dash number fixes a size. A military designator fixes a size and a compound specification. MS28775-911 and M83248/1-911 are the same 0.863 × 0.116 in part in two different materials — they are not interchangeable.

03Available compounds

same tool, 15 materials

Every compound below is moulded in the AS568-911 tool, so the dimensions do not change when you change material. Temperature bands are the continuous service range for the standard formulation.

04Questions we get on this size

What is AS568-911 in millimetres?

21.92 mm inside diameter × 2.95 mm cross-section, outside diameter 27.81 mm. These are converted from the inch values at 25.4 and rounded to two decimals — a metric drawing will normally specify a different, rounder size.

What is the outside diameter?

1.095 in (27.81 mm), calculated as ID + 2 × CS. This is the free, uninstalled diameter. Installed in a groove the ring stretches slightly and the OD you measure on the part will not match this number.

Is a mil-spec number for this size the same part?

Same geometry, different material specification. A designator such as MS28775-911 fixes the compound as well as the size. If you substitute a different compound for the same dash number the part will fit, but its swell in the medium and its compression set at temperature will differ — which is what the material callout was there to control.

Can you make it in FFKM or another special compound?

Yes, to order. FFKM and the perfluoroelastomers are compression moulded for this size rather than transfer moulded, so tooling cost applies and lead time is around four weeks. It is normally only worth it above 200 °C or in solvents that swell FKM.

05Other sizes in this cross-section

0.116 in · 900 series

A groove cut for one 0.116 in section takes any of these. Change the ID without changing the groove depth.

All 0.116 in sizes